18 Reviews
Horsepower : 1.5 hp ; Rotation Speed : 3450 rpm ;
Motor Review
Perfect fit for a Craftsman Table Saw 317 series. Plenty of power quite and well balanced. good replacement motor price was good
0
Horsepower : 0.75 hp ; Rotation Speed : 1725 rpm ;
So far so good
I have this running a homemade 55 gal drum dirt trommel with a double reduction gear. It’s been smooth and reliable so far. Only have an hour on it, will update if it fails.
0
Horsepower : 1.5 hp ; Rotation Speed : 3450 rpm ;
Great product so far.
I bought it as a replacement motor for my Sears - Craftsman 10\" Table Saw. The specs matched with regard to 1.5HP and 3450 RPM and another reviewer said it was a direct-bolt replacement. Having said that, the motor comes with 6 internal wires and a ground terminal all which need to be wired to your own 3-wire cord. It's up to you to decipher the chart as to whether you're going to run in 120v or 230v, as well as Clockwise or Counterclockwise rotation. So, you'll be staring at the chart for that a while and basically figuring out which 3 wires go to the hot wire of your own cord and which other three go to the neutral (for two sets of 4 wires nutted together total). The directions say it's pre-wired for 120v but, after studying, mine was clearly set for 230. It also hinted that it may be set for Counterclockwise rotation but mine was clockwise. Other than that, the motor is larger than my original and did bolt up fine however, the larger motor size pushed the shaft sideways out of alignment with the pully on the table saw. I simply flipped the pully the opposite direction on the motor to ride closer to the motor housing and got both pullies to line up. Minor note: Since the motor comes with a wire box and punch hole for your power cord, I wish it came with a cable clamp for the box. Looking forward to another 30 years of use out of my table saw.
0
Horsepower : 1.5 hp ; Rotation Speed : 3450 rpm ;
Great motor
Great motor. Easy to wire in.
0
Horsepower : 1.0HP ; Rotation Speed : 3450 rpm ;
as described
as described
0
Horsepower : 1.0HP ; Rotation Speed : 3450 rpm ;
envelope dims are perfect
motor conforms to the international envelope dimensions of the motor. The wiring diagrams are easy to read for the selected voltage option. good product. installed yesterday and working fine.
0
Horsepower : 0.75 hp ; Rotation Speed : 1725 rpm ;
3/4 hp motor
Motor arrived several days after ordering, sooner than expected. Opened box and spun shaft, spun easy. Hooked up motor to an old drill press I’m working on. Motor has a slight vibration but not bad. Amps checked out good. Have only used a couple of times but seems to be worth the price for a motor that will only be used every once in a while.
0
Horsepower : 2.0 HP ; Rotation Speed : 1725 rpm ;
Works great
It is a little heavy but works great for me. I used to make a meat grinder
0
Horsepower : 2.0 HP ; Rotation Speed : 1725 rpm ;
Owner
Works well, I did wire it 220v due to current draw. Meets expectations and works well as a replacement on belt sander.
1
Horsepower : 2.0 HP ; Rotation Speed : 1725 rpm ;
Engineer
Replace an old 1.5HP compressor motor with the 2HP electric motor 1725 RPM running with 230v, worked as it should (had to change to run Clockwise vice CCW as it came running CCW. Wiring was easy to understand (if you are use to working with motor wiring). Seems heavy duty, quiet and smooth. Started the old 2 stage compressor with no issues. Would recommend.
0